Wooden Ships Comments on thisClaud Worth inspired gaff cutter
Claud Worth inspired gaff cutter, built by Pete Nash of Dartmouth. It is not often we come across a boat that truly is right. This magnificent little yacht however is just that, everything about her is as it should be, from her design to her construction, her quality of finish and the way she handles and sails.
Built by Dartmouth shipwright Pete Nash for himself to a design inspired by Claud Worths Tern III. The lines were scaled down with the help of naval architect Ed Burnett to produce an exquisite looking yacht. Gently curved bow with a slightly raked keel and a stern post hung rudder. The sheer line is simply brilliant, dipping down to a low point just forward of the cockpit and then turning swiftly up to the elegant Claud Worth trademark counter.
At 37 this is a great size of yacht, she is large enough to have a comfortable interior with 6 berths, standing headroom and a saloon to seat 6 people, but not so large that she needs an experienced crew to handle her. The owners have cruised and raced with the boat as a husband and wife crew and find her very easy to handle with just the two of them. The self tacking jib, self tailing bronze winches, electric anchor windlass and lightweight hollow spars are just some of the features that make her a very easy boat to handle and sail.
There really is very little afloat that can compare to this yacht, her build quality and choice of materials is second to none and the way she sails and handles is an absolute delight. She has had her annual refit this spring including varnishing the mast, replacement of leather work in the rig, all brightwork on deck and the spars re-varnished with Epifanes, complete engine service, antifoul and anodes.
Length overall 49
Length on Deck 37
Displacement 12 tonnes
Video by Imogen Moody.
Top 3 planks of aged pitch pine reclaimed from the dockyard. The rest of the 1 planking is of air dried close grained larch. There are no butt joints in any of the planking, instead the planks have been joined where necessary with 26 scarph joints.
Built with 3 x 2 grown oak frames at 24 centres with 2 steamed oak intermediate timbers of 2 x 2 sections. This is all copper rivet fastened. Hood ends and garboards fastened with silicone bronze screws. Each seam has been caulked with 3 strands of cotton before being splined. The whole hull was then sheathed with 210g epoxy cloth to give an absolutely tight and fair finish that requires less maintenance than a conventionally finished hull.
Grown oak lodging knees with cast bronze hanging knees all fastened with bronze bolts. The heads of each bolt have been finished to look like rivet heads giving a much softer appearance.
Oak backbone approximately 10 x 7 with a laminated Iroko stem stretching from the stem head to aft of the mast step meaning there are no scraphs to work and open up.
Grown oak floor on every grown frame, through bolted with bronze bolts. There are two stainless steel strap floors in way of the mast step where there is no space for a large oak one. In order to remove any potential for electrolytic action the bronze floor bolts used here have been insulated from the stainless with especially turned nylon bushes.
4.5 tonne external lead ballast keel fastened with 12 bronze bolts set through the back bone in pairs. tonne of internal lead trimming ballast fastened securely in the bilge.
Decks and cockpit
Deck is laid on pine deck beams set on the outer ends into the beamshelf in the usual way. marine plywood screwed and glued to the deck beams with scarphed joints. The underside has been Vd using a router to give the appearance of a solid laid teak deck. The deck head is finished with an easily wiped high gloss paint.
Yacht laid swept teak deck with no butt joints is bonded to the plywood with epoxy and joggled to a varnished king plank. The use of epoxy to bond the teak to the ply means there are no plugs showing on the surface and no fastenings through the ply to allow water ingress.
Upstanding varnished toe rail all round with a varnished capping rail. King plank, coverboards, toe rails and capping rail in finest quality reclaimed Burma Teak.
Low profile coachroof flows nicely aft into the cockpit with the companion hatch joining the two.
Burma Teak coachroof coamings with three small round bronze portholes each side. Epoxy sheathed marine plywood coachroof deck with a slight camber giving it a superb line. Varnished teak handrails and a butterfly skylight on the coachroof.
Very comfortable self draining cockpit with slightly reclined and curved teak coamings which sweep round at the forward end into the companion hatch. Scrubbed teak thwarts which lift to give access to large lockers and teak cockpit sole gratings.
Slightly raised bridge deck with a step up to the companion hatch. The hatch is designed in a similar fashion to the hatches seen on the pilot cutters, raised at the aft end and raking gently down to the coachroof at the forward end with a camber across the sliding hatch.
Forehatch of varnished Burma teak with a built in dorade vent and bronze cowling is offset slightly to port allowing the bowsprit to run inboard when necessary.
The rig plan was designed by naval architect Ed Burnett.
Gaff cutter rig on a keel stepped hollow Douglas Fir pole mast. Solid built Douglas Fir gaff, boom and bowsprit. All spars built by Pete Nash.
Stainless steel standing rigging to stainless rigging screws and external stainless chainplates mounted on channel boards. Rigging screws covered by stitched leather jackets. Twin lower shrouds to the hounds and a single cap shroud over spruce spreaders.
Inner forestay to the stem head, outer forestay to the bowsprit end which is tensioned with a block and tackle on the foredeck. Wickham Martin furling gear on the outer jib. Running backstays on tackles which are split to provide support to the hounds and the cap of the mast. Staysail is now self tacking, mounted on a staysail boom with a bronze horse on the deck.
All blocks at deck level are varnished wood, all blocks aloft are Tufnell which are strong and lightweight. All running rigging is braid on braid giving a traditional feel to the rig. Galvanised pin rail mounted on the deck by the shrouds to carry the halyard falls.
Bronze boom gallows fixed to the aft cockpit coaming support the boom when the mainsail is dropped, another small but important addition to make the boat very easily handled by a small crew.
All sails new by Westaway in 2005. Stored ashore every winter, laundered and repaired as necessary. Mainsail, topsail, staysail, No.1 jib and No.2 jib.
Topsail sets on the pole mast with no need for an extra jackyard making it a very simple and easy process to set.
2 pairs of bronze Wilmex 315 self tailing winches mounted on the cockpit coamings for the jib and staysail sheets.
Single bronze Lewmar ST winch mounted on the forward side at the base of the mast.
Beta Marine 37hp 4cyl diesel installed new, now with 700 hours. Single lever controlled gearbox with a centreline stainless steel shaft to a 3 blade bronze propeller
The whole engine installation is extremely tidy and professional with excellent access all around and from above through the lifting hatch in the cockpit sole.
4 x 12v deep cycle high capacity batter....
|Engine Make/Model:||Beta Marine 37hp 4cyl |